hello, welcome to guangdong source lei powder limited company website!
+86-757-22910350 中文版 ENGLISH
Home
About Us
Products
Barium Sulfate
Calcium Carbonate
Talcum Powder
News
Contact Us
NEWS CENTER
Company News
Industry News
Technical exchange
Service Hotline: 86-757-22910350
Yuan Lei's Little Knowledge | Which Coating (IV) Are Different Mineral Powders Suitable
Non-metallic minerals are mainly used as functional fillers in the coatings industry. The purpose is to reduce the cost of coatings; increase the consistency of latex paint, improve the suspension of pigments in the paint; give coatings functionality and improve their properties, including gloss, hiding Power, flow and homogenization, durability, film thickness, penetration and rheology. There are many kinds of mineral fillers and their performance varies greatly. Therefore, it is the key for non-metallic mineral powder manufacturers to open the coating market to thoroughly understand the performance and best application of mineral fillers. Originally, most effective anti-corrosion pigments were based on chromium and lead salts. Now these two salts will produce toxic underground pollution and environmental concerns. The characteristics of fillers used in anti-corrosion coatings include low chemical reaction, hydrophilicity, low oil absorption, mainly talc, wollastonite, barite, mica powder and the latest rise of graphene. (1) Talc and barite Talc is an important mineral that reduces the water permeability of the paint film, and barite can improve the weather resistance and acid and alkali resistance of the paint in addition to the lowest oil absorption. (2) Wollastonite Wollastonite is used to increase the tensile strength of the coating and reduce cracks, especially the wollastonite treated with silane coupling agent, and another important feature is anti-corrosion. For example, wollastonite can be used as an anti-corrosion agent to partially replace expensive zinc phosphorus salt anti-corrosion pigments for water-based epoxy metal primers. (3) Illite In the epoxy resin system, illite is a high-quality functional filler. Epoxy resin and amine curing agent after the crosslinking reaction of the coating is alkaline, the alkaline of the ilite powder added to the coating, can promote the full curing reaction of amine and epoxy, plus itself is alkaline, enhance the alkaline coating, the corresponding improve the anti-corrosion performance of the coating, and reduce the production cost. (4) Graphene Graphene is easy to form a dense film in the coating due to its good shielding and large specific surface area, which is of great help to improve the anti-corrosion performance. Studies have shown that CVD-grown graphene can form a protective layer on the surface of copper, aluminum and other metals to prevent metal oxidation and corrosion. The graphene prepared by redox can be mixed with organic resin to prepare composite coating, which can play the shielding effect of graphene and the excellent adhesion ability of resin, and achieve the purpose of long-term anti-corrosion. Compared with ordinary coating, the graphene coating prepared by redox can reduce the corrosion rate of low alloy steel by 1 order of magnitude. (5) quasi spherical silicon powder The quasi-spherical silica powder can be enriched into the structure of the coating in the anti-corrosion powder coating, forming a dense and strong coating film, which plays a role of chemical passivation and physical sealing. (6) Mica powder Mica flakes from a wide range of sources, cheap, with excellent insulation, elasticity and flexibility, diameter-thickness ratio, small thermal expansion coefficient, inert in a variety of chemical media, anti-ultraviolet radiation, the coupling agent surface treatment, can replace expensive glass flakes and stainless steel flakes, thereby reducing costs. In addition, the mica flake has 20-1000 mesh specifications, and mica powder of different specifications and grades can be selected to increase the compactness of the paint film and reduce the air permeability of the paint film. For example, the mica flake is used in the preparation of water-based silicone acrylic latex paint, which effectively improves the water resistance and chemical medium corrosion resistance of the paint film.
09
2023
/
06
Yuan Lei's Little Knowledge | Which Coating (III) Are Different Mineral Powders Suitable
Non-metallic minerals are mainly used as functional fillers in the coatings industry. The purpose is to reduce the cost of coatings; increase the consistency of latex paint, improve the suspension of pigments in the paint; give coatings functionality and improve their properties, including gloss, hiding Power, flow and homogenization, durability, film thickness, penetration and rheology. There are many kinds of mineral fillers and their performance varies greatly. Therefore, it is the key for non-metallic mineral powder manufacturers to open the coating market to thoroughly understand the performance and best application of mineral fillers. 1. high solid coating Generally, coatings with 55% solids can be called high-solids coatings, and their main requirements for pigments and fillers are: under normal shear stress, they have little effect on the binder. In the high solid coating, the connecting network of the coating film is relatively fragile and the viscosity is poor. Due to the absorption of moisture, in order to avoid loss of adhesion, weakening of the inherent corrosion resistance and foaming, the surface of the filler must be hydrophilic, with a small surface area and a flake shape. (1) Talc Talc is a microcrystalline mineral with small surface area, which is suitable for high solid protection and marine coatings. Due to the good barrier effect of talc, its traditional use is in industry and ship maintenance. Although the high oil absorption of talc increases the viscosity of the coating, talc can still be used in high-set coatings by strictly controlling the particle size. (2) Kaolin Kaolin with low oil absorption can be well used in high-solid coatings, which is beneficial to improve the viscosity stability of the coating, enhance the anti-cracking mechanical force and erosion resistance, and can be used to prepare high gloss and high smoothness topcoat. (3) barite and barium sulfate When high gloss and strong wear resistance are required, barite is often used as a filler for high-solid coatings, such as high-solid industrial topcoats. 0.7-0.8μm micro-powder grade precipitated barium sulfate is used for high-solid finish, which can reduce VOC and replace some expensive titanium dioxide. 2. radiation treatment coating Most conventional fillers can be used in radiation treatment coatings. The type and amount of minerals ultimately depends on the requirements of the finished product. For example, in radiation-treated coatings applied to the surface of wood materials, fillers are generally used in an amount of 10-40% in order to obtain good wear and corrosion resistance. Under normal circumstances, the selection of minerals with low refractive index can minimize the influence of fillers on the treatment effect. Now, the improvement of the lighting system has allowed the radiation treatment of colored coatings, and the ability of minerals to absorb the ultraviolet spectrum (such as talc, kaolin, mica) should also be fully considered in the selection of fillers. Barite is used in radiation treatment coatings to play the role of sand doping, talc as filler in order to obtain a high smooth surface of the primer, and the use of different particle size of calcium carbonate, both as a filler and can reduce costs, silica can be used as a matting agent.
07
Yuan Lei's Little Knowledge | Which Coating (II) Are Different Mineral Powders Suitable
Non-metallic minerals are mainly used as functional fillers in the coatings industry. The purpose is to reduce the cost of coatings; increase the consistency of latex paint, improve the suspension of pigments in the paint; give coatings functionality and improve their properties, including gloss, hiding Power, flow and homogenization, durability, film thickness, penetration and rheology. There are many kinds of mineral fillers and their performance varies greatly. Therefore, it is the key for non-metallic mineral powder manufacturers to open the coating market to thoroughly understand the performance and best application of mineral fillers. powder coating As a solvent-free coating, powder coating has the characteristics of economy, environmental protection, high efficiency and excellent performance. The fillers used in powder coatings are mainly barite, calcium carbonate and wollastonite. The choice of filler depends on the type of resin used, gloss requirements, mechanical properties and the end use of the coating. (1) Wollastonite Powder coatings with wollastonite as filler have natural luster, much lower than powder coatings with barite and calcite as filler, wollastonite can enhance the mechanical strength and corrosion resistance of the coating. (2) Barite Barite has a higher hiding rate and longer lasting high gloss than calcite. Barite has the characteristics of chemical inertness and low oil absorption, which will only slightly reduce the fluidity and smoothness of powder coatings. The typical dosage range of barite filling is 5-30%, the powder coating is solid, and the weight is the sales unit. The large proportion of barite can satisfy the manufacturer. Compared with precipitated barium sulfate, the advantage of natural barite is that natural barite with low heavy metal content can be used, and the price is cheap. (3) Mica powder Mica powder is composed of complex silicate, the particles are scaly, heat resistance, acid and alkali resistance is excellent, has an impact on the melt fluidity of powder coatings, generally used in temperature and insulating powder coatings, can be used as texture powder filler. (4) Heavy calcium carbonate Because most of the places where heavy calcium is applied are not very strict about the fineness, the heavy calcium currently on the market is generally not surface treated. However, due to poor fluidity of powder coatings, ultrafine heavy calcium carbonate should generally be surface modified. The modifier uses more coupling agents such as titanate, phosphoric acid, surfactant, aluminum sulfate and sodium hexametaphosphate, etc. Sometimes fatty acids are also considered. In recent years, there have been some examples of using polymers as surface treatment agents. Through modification, the amount of calcium carbonate can be increased by 20% ~ 50%, and the gloss and leveling are increased. Because heavy calcium carbonate is non-toxic, it has a market base in non-toxic powder coatings, such as strollers, toys, etc.
01
Yuan Lei's Little Knowledge | Which Coating (I) Are Different Mineral Powders Suitable
Non-metallic minerals are mainly used as functional fillers in the coatings industry. The purpose is to reduce the cost of coatings; increase the consistency of latex paint, improve the suspension of pigments in the paint; give coatings functionality and improve their properties, including gloss, hiding Power, flow and homogenization, durability, film thickness, penetration and rheology. There are many kinds of mineral fillers and their performance varies greatly. Therefore, it is the key for non-metallic mineral powder manufacturers to open the coating market to thoroughly understand the performance and best application of mineral fillers. water-based coatings Water-based coatings are a class of environmentally friendly coatings that have developed rapidly in recent years, and their solvents are mainly water or water-based solvents. In addition to all mineralogically useful features, the role of the chemical composition of the filler is very important in waterborne coatings. One is that the mineral filler should be stable under acid and alkali conditions, and the water soluble matter has little water content. These characteristics are particularly important in the anti-corrosion coating series; Second, in order to obtain good activity (wettability) and dispersibility, mineral fillers must be hydrophilic, otherwise they will flocculate; Third, the specific surface area is low, because the amount of adhesive and surfactant in the coating is extremely small, and the adhesive ability and hindering function of the emulsified resin (adhesive) are not high. Considering the cost, the amount of adhesive should be as small as possible. (I) talc Talc has a good hydrophilic character and does not disperse thoroughly in water unless a deflocculant is added. Where the activity and dispersing power must be increased, the lamellar morphology of the talc must be retained in order to enhance the mechanical properties (resistance to cracking). In interior wall coatings, talc can be used as a flow regulator, matting agent and titanium dioxide supplement. Talc also improves the wash-off resistance of the coating. (II) kaolin Because of good hydrophilicity, kaolin in water-based coatings dispersion is very good, can be used to induce thixotropy and improve the anticoagulant, but also to improve the ability to wash and improve whiteness, irregular granular coarse kaolin can reduce the coating gloss. Calcined kaolin has a low aging rate, so it can also be used as a building exterior wall coating. Without affecting the gloss of the coating, with ultrafine high whiteness of kaolin can replace 10-20% of titanium dioxide, when the particle size of kaolin and titanium dioxide is very similar, can be a good place to replace the space occupied titanium dioxide particles. (III) Wollastonite and Nepheline Syenite-like Minerals Wollastonite and nepheline syenite minerals are alkaline minerals (pH 10), especially suitable for water-based paint series, they can improve the storage stability of paint. Since nepheline syenite is well suited for use in waterborne coatings, the modification of waterborne coatings requires only an increase in the amount of mineral used in the nepheline syenite, which is now used as a functional filler in new surfactant-free coatings because it is readily dispersible in the waterborne series of coatings. (IV) dolomite Dolomite has high brightness, flake, small particle size (D50=0.3~0.4 μm), hydrophilic, can be used as a substitute for titanium dioxide, in white paint instead of 30% of titanium dioxide, without affecting the hiding power of the coating.
30
05
Yuan Lei's Little Knowledge | What are the differences in the application fields of different kaolin
高岭土是一种非金属矿产,是一种以高岭石族粘土矿物为主的粘土和粘土岩。因呈白色而又细腻,又称白云土。 高岭土用途十分广泛,主要用于造纸、陶瓷和耐火材料,其次用于涂料、橡胶填料、搪瓷釉料和白水泥原料,少量用于塑料、油漆、颜料、砂轮、铅笔、日用化妆品、肥皂、农药、医药、纺织、石油、化工、建材、等工业部门。 随着改性技术和纳米技术的出现及发展,改性高岭土和纳米高岭土展现出了更加优异的性能,极大地拓展和延伸了高岭土的应用领域。 普通高岭土 高岭土良好的性能使其在陶瓷、造纸、环保和建材等各领域中得到广泛应用。 (1)陶瓷领域的应用 陶瓷是高岭土使用量最多的领域之一。适宜的使用高岭土量可以使陶瓷获得更好的稳定性、白度和强度等性能。 (2)造纸领域的应用 高岭土应用于造纸领域可使纸张获得良好的白度、光泽性、吸油性和光滑度性能,是一种重要的造纸填料。 (3)在涂料领域的应用 由于亲水性好,高岭土在水性涂料中分散性好,可用来诱导触变并改善抗凝性,也能改善耐冲洗能力、提高百度,不规则粒状粗粒高岭土可减少涂层光泽。 由于煅烧高岭土的老化率低,因此可作为建筑外墙涂料。 (4)耐火领域的应用 高岭土在600~900℃下烧结脱水形成的硅酸铝称为偏高岭土,其为一种重要的高岭土加工产品,通常作为高性能矿物掺合料而应用于建筑材料领域。以偏高岭土替代Al2O3、高铝水泥制备耐火浇注料,可提高耐火材料的抗折强度,减少裂纹,获得良好耐火性能的同时,还可大幅降低生产成本。 改性高岭土 高岭土通过改性可以提高其可塑性、耐火性和比表面积等应用性能,获得某些新的功能,从而提高其附加值,使其适应不同领域的应用要求,并在应用中获得更优良的表现。 改性高岭土主要应用于环保、建材和橡胶等领域,在目前工业生产中备受青睐。 (1)环保领域的应用 改性可使高岭土获得更大的比表面积,增强其吸附性能,使其在污水处理等环保领域具有更好的应用性能。 (2)陶瓷领域的应用 改性高岭土优良的吸附性能还被制成功能陶瓷用于微生物灭菌,同时通过改性可使高岭土获得杀菌性能。 (3)二次资源利用领域的应用 改性高岭土还被用于二次资源利用领域,用于回收金属离子。 (4)橡胶和建材的应用 经过煅烧改性的高岭土可增强绝缘性、稳定性和耐腐蚀性,其优异的性能使其成为一种成本较低的高效填料,改性高岭土也被用于改善建材的应用性能。 纳米高岭土 纳米级高岭土颗粒具有表面效应和小尺寸效应等纳米特性,使其在应用中获得更好的以及某些独特的性能,展现了更高的应用价值,因而成为高岭土应用研究的热点。 纳米高岭土主要作为填料应用于水泥、橡胶和润滑剂等领域,还被用作纳米反应器和隐身材料等。 (1)建材领域的应用 纳米高岭土被用于改善水泥的应用性能,纳米高岭土的掺杂使水泥的力学性能及耐久性均得以改善,水泥中掺加纳米高岭土明显降低了氯离子的渗透系数,使纳米高岭土改性水泥可以在海洋和融雪等恶劣环境下使用。 (2)橡胶领域的应用 在橡胶中加入适量的纳米高岭土,可使橡胶的抗老化性能和抗压缩疲劳性能获得较大提升,同时还可以提高生产的安全性。将纳米高岭土与卤锑阻燃剂复配用于阻燃低密度聚乙烯,纳米高岭土替代20%的Sb2O3可使氧化指数及各项力学性能最优,显著减少Sb2O3的用量,降低对环境的污染,提高安全性。 (3)润滑领域的应用 高岭土具有层状结构和小颗粒尺寸使其具有较好的润滑性,纳米高岭土的小尺寸效应更是增强了其润滑性能,因此纳米高岭土也被应用于润滑剂中。
26
Yuan Lei's Little Knowledge | Process Application of Calcium Carbonate Filler Masterbatch in Non-woven Fabric
Manufacturing Process of Calcium Carbonate in PP Spunbond Non-woven Fabric The raw material used in the production of PP spunbond non-woven fabrics is high melting index polypropylene, which is evenly mixed with calcium carbonate filling masterbatch, and then enters the continuous pre-filter after being extruded and melted by the hopper into the screw extruder, and then enters the spinning box. The melt enters the spinning head through the metering pump, and the melt is transported to the spinneret quantitatively by the metering pump, and a continuous melt trickle is formed through the spinning hole, I .e., the primary fiber. The as-spun fibers are then cooled by a quench air and drawn to form a filament bundle. The filament bundle is swung back and forth by the swing roller, and is evenly laid on the running screen curtain to form a fiber web. Why choose calcium carbonate to do filling masterbatch? Calcium carbonate is an extremely important inorganic chemical product, which is widely used in plastics, rubber, paint, paper and other industries. The characteristics of several fillers commonly used in industry are as follows: Calcium carbonate: the purpose of adding filler masterbatch in spunbond non-woven fabric is to reduce the cost. From the experience of plastic resin modification function and cost reduction, the most cheap and easy to obtain, the appearance is white and tasteless powder. The relative density is 2.71, the refractive index is 1.65, and the Mohs hardness is 3. Aged soil: easy to disperse, the price is relatively higher than calcium carbonate, the appearance is white, the relative density is 2.6, the refractive index is 1.56. Talc powder: easy to disperse, the processing of equipment has a certain lubricity, with solid crystalline white powder. Want to density between 2.7~2.8, and the price is relatively expensive. Mica powder: the relative whiteness is lower, because mica powder is non-toxic and can be used in food contact products, the relative density is between 2.8 and 3.0, the refractive index is 1.59, and the Mohs hardness is 3. Wollastonite: 2.9 relative density, 1.63 refractive index, Mohs hardness 4.5, the biggest advantage is not hygroscopic, and the color masterbatch has little effect. Therefore, the general selection of fillers in the production process of non-woven fabrics are generally based on calcium carbonate, and the appropriate addition of a little high-age soil or wollastonite to increase the dispersion and transparency in the production process. Generally, the mesh number of calcium carbonate is above 1500 mesh, and it cannot be too fine, because the price of too fine mesh number is high, and ultrafine powder is generally not dispersed. Filling method of filling material Without changing the production equipment and production process conditions, the filler is added in the hopper of the masterbatch, but the addition ratio will be limited. Since the filling of the masterbatch reduces the cost, the higher the filler concentration in the masterbatch, the lower the cost, and the smaller the addition ratio. On the contrary, the higher the concentration, the higher the cost, and the more the addition ratio. And the production of functional masterbatch can not be filled with masterbatch, so as not to affect its functionality.
16