hello, welcome to guangdong source lei powder limited company website!
+86-757-22910350 中文版 ENGLISH
Home
About Us
Products
Barium Sulfate
Calcium Carbonate
Talcum Powder
News
Contact Us
NEWS CENTER
Company News
Industry News
Technical exchange
Service Hotline: 86-757-22910350
Yuan Lei's Little Knowledge | What is Powder Coating
Powder coatings are completely different from general coatings, and they exist in the state of fine powder. Because no solvent is used, it is called powder coating. The main features of powder coatings are: harmless, high efficiency, resource saving and environmental protection. Classification: There are two main categories of powder coatings: thermoplastic powder coatings and thermosetting powder coatings. Thermoplastic powder coatings are composed of thermoplastic resins, pigments, fillers, plasticizers and stabilizers. Thermoplastic powder coatings include polyethylene, polypropylene, polyester, polyvinyl chloride, chlorinated polyether, polyamide, cellulose, polyester, etc. Thermosetting powder coatings are composed of thermosetting resins, curing agents, pigments, fillers and additives. Thermosetting powder coatings include epoxy resin-based, epoxy-polyester-based, polyester-based, polyurethane-based, acrylic resin-based, and the like. Disadvantages: uneven powder on the corners, difficult to cover up the defects of the cured coating, high curing conditions, limited use of the substrate. Features: 1. The product does not contain toxicity, solvents and volatile toxic substances, so there is no poisoning, no fire, no "three wastes" emissions and other issues, fully in line with the requirements of the national environmental protection law. 2. After the pre-treatment of the coated object, one-time construction, no primer, you can get enough thickness of the coating, easy to realize automatic operation, high production efficiency, can reduce costs. High utilization rate of raw materials. 3. It is beneficial to the health of construction personnel and environmental sanitation. The powder attached to the construction personnel can be blown off with compressed air or washed off with ordinary soapy water. 4. Powder coating storage, transportation are safe and convenient. 5. The coating is compact, good adhesion, impact strength and toughness, high corner coverage, excellent chemical corrosion resistance and electrical insulation properties. Advantages: 1, health and environmental protection: eliminating the need to achieve coating performance and add a variety of liquid chemical harmful film forming, dispersion, wetting, leveling, anti-corrosion mildew and other additives. 2, convenient transportation and storage: powder coating, neither water, nor solvent, is completely solid, convenient and safe transportation, when the transportation and storage temperature is lower than 0 ℃, powder coating will not freeze. 3, no preservatives: traditional liquid paint, both water, and bacteria food, easy to be contaminated by bacteria. Therefore, in order to prevent deterioration, it is necessary to add preservatives, and latex powder coatings have no bacterial contamination problems and do not require preservatives. 4. Paint odor: Compared with the general traditional paint odor residue, this paint can be dispersed quickly, which can be said to be immediately eliminated. Disadvantages: curing conditions have certain limitations. Application: 1. Decorative protective coating Used for household appliances, metal furniture, automobiles, instruments, bicycles, sewing machines, mechanical and electrical equipment, light industrial equipment, agricultural machinery, construction hardware and other products of the shell and parts; 2. Insulation and moisture-proof coating Used in transformers, iron cores, coils, resistors, batteries, etc. for motors, electrical appliances, electronic components and other products; 3. Anti-corrosion coating Used for chemical pool tanks, oil pipelines, drinking water pipelines and valve bodies, household goods, electroplating fixtures, etc. 4. Building painting Suitable for building doors and windows, door locks, metal structures and pipe fittings, engineering equipment and other outdoor facilities. 5. Antistatic powder Performance is similar to the insulation powder coating, used in the room and other anti-static place.
07
2022
/
12
Yuan Lei's Little Knowledge | Requirements of Calcined Kaolin in Coatings
煅烧高岭土用于涂料行业可减少钛白粉的用量,使涂膜具有良好的特性,可改善涂料的加工、储存和应用性能。煅烧高岭土在中高档涂料中的用量为10~30%,使用的煅烧高岭土以-2um为含量70~90%为主。那么煅烧高岭土在涂料的运用中有什么指标要求呢? 涂料对煅烧高岭土要求分别是白度、粒度、遮盖力、分散性、325目筛余物、吸油值、沉降体积、pH值、耐候性、耐酸耐碱性能。 01 白度:白度是高岭土工艺性能的主要参数之一,纯度高的高岭土为白色,因此白度应越高越好,至少大于90%,有得厂家会要求大于93%。白度的稳定性也是很重要,如果波动很大会影响到涂料的光学性能,使同一配立下不同批次产品出现色差。 02 粒度:对于煅烧高岭土生产厂,成品的检验指标应为-2μm在80%左右。当然,不同原料生产的产品性能会有不同,如果其他指标合格的话,粒度的要求还可以降低。煅烧高岭土粒度的检测方法通常有离心沉降法、重力沉降法、激光分析法等。 粒度主要受原矿易磨性和煅烧温度影响。易磨性受原矿品质决定,主要影响生料阶段的粒度,煅烧温度主要影响窑后打散的粒度。涂料用煅烧高岭土应用中温煅烧(1000~1200℃),选择最佳煅烧温度则是在非晶相刚刚转变为硅铝尖晶石相,此时产生多孔膨体结构,造成孔隙发育,产品的磨耗值相对较低。 03 遮盖力:遮盖力是涂料对煅烧高岭土最看重的一项指标。遮盖力是指当一件物体涂以某种涂料时,涂料中的颜料能遮盖被涂物体表面的底色,使这底色不能再透过涂料而显露出来的能力。如果要涂同一块表面,所用颜料的遮盖力越大,则需要的颜料量变越少。 04 分散性:虽然煅烧高岭土经过了超细粉碎,平均粒径能达到≤1μm,但在涂料的高粘度的母液里面,颗粒间不是单独的而是相互团合在一起。 煅烧高岭土在涂料体系里能分散开来的这种能力叫做分散性。一般煅烧高岭土的分散性与磨矿的最终效果有关,如果在超细加工过程中含有45μm或更大的颗粒,那么在涂料体系里无论如何也分散不开。因此对该项指标的要求是小于45μm,且越小越好,分散性测试可用海格曼粒度仪。 05 325目筛余物:涂料行业对高岭土325目筛余物的要求是<0.02%,且越小越好。 06 吸油值:涂料要求煅烧高岭土的吸油值为50-60g/100g算是适中,吸油量高,则相同配方制成的涂料粘度就大,因此想要降低粘度就必须增加漆基的量,增加成本;吸油值低,则制成的涂料就容易沉降,导致开罐性能差。 07 沉降体积:降体积反映了煅烧高岭土在涂料中的沉降性能,直接影响到涂料的开罐性能。该项指标应越高越好,越高则颜料越不容易沉降,就会在涂料中保持良好的均匀性。 08 pH值:pH值反映了煅烧高岭土的酸碱性。涂料要求其值应在6-8之间,基本上接近于中性。 09 耐候性:颜料能抗拒发生上述变化的能力叫耐候性。涂料中填加煅烧高岭土后,可以屏蔽紫外光照射,提高涂料的耐候性,延迟粉化变色,增强涂层的综合机械性能和耐污自洁性。 10 耐酸碱性:煅烧后的高岭土在常温下不与任何酸碱起反应,也不会与其他任何物质起化学反应,因此煅烧高岭土具有很好的耐酸耐碱性能,能够良好的与其他物质混合的性能。 涂料对煅烧高岭土的其他指标要求,还有混合性能、湿润性能、密度等,这些是所有煅烧高岭土的共性,有些不是数字化的指标。
Yuan Lei tells you | 5 common purification methods of high purity quartz sand
Source Lei tells you | 5 common purification treatment methods for high-purity quartz sand High-purity quartz sand is the material basis for the development of high-tech industries, and its application fields involve optical fiber, military, aerospace industry, etc. In these fields, the purity requirements of quartz sand raw materials are extremely strict, and the impurity content in quartz sand is very low, especially for Fe, Al and other impurities. Therefore, quartz sand purification technology is related to the long-term development of China's high-tech fields. At present, the purification technology of high purity quartz sand is monopolized by the United States, Germany and other countries, and restricts the export of purification technology and products, so it is of great significance to master the purification technology of high purity quartz.
02
2021
Yuan Lei tells you | Mineral fillers and their role in coatings
Yuan Lei tells you | Mineral fillers and their role in coatings. Fillers are also called fillers, which are a kind of materials added to materials (such as plastics, rubber, adhesives, papermaking, coatings, chemical fibers, power electronics, ceramics, glass, refractory materials, cementing materials, inks, etc.) for filling. It is a relatively inert material, which can reduce costs, improve performance, and improve process characteristics. Fillers can be divided into two types: one is an inert filler that adds cheap materials to higher-priced materials in order to reduce costs and does not change the performance of the material; the other is a functional filler with special functions, such as electricity.
Yuan Lei told you | the application of fillers in water treatment. How many types of fillers are there?
Source Lei tells you | the application of filler in water treatment, how many types of filler? Filler refers to the material filled in other objects. In chemical engineering, packing refers to the inert solid materials installed in the filling tower, such as Pall ring and Raschigo ring, etc., its role is to increase the gas-liquid contact surface, so that they are strongly mixed with each other. In chemical products, fillers, also known as fillers, are solid materials used to improve processing performance, mechanical properties of products and (or) reduce costs. In the field of sewage treatment, mainly used in contact oxidation process, microorganisms will accumulate on the surface of the filler, in order to increase the surface contact with the sewage, the sewage is reduced.
Yuan Lei tells you about the application and development trend of powder fillers.
Yuan Lei tells you | Talking about the Application and Development Trend of Powder Fillers In the era of environmental storm of coatings, the development of environment-friendly coatings is an inevitable choice for enterprises, but environment-friendly coatings are not only water-based coatings. If enterprises rush to develop water-based coatings, it is inevitable that products will be homogenized. In addition to water-based coatings, high-solid coatings, solvent-free coatings, and powder coatings are also environmentally friendly coatings, which should become the key development direction of the coatings industry. According to a research report, the value and volume of the powder coatings market in the Asia-Pacific region are expected to reach the highest growth rate from 2017 to 2022. Powder coating technology is rapidly developing