hello, welcome to guangdong source lei powder limited company website!
+86-757-22910350 中文版 ENGLISH
Home
About Us
Products
Barium Sulfate
Calcium Carbonate
Talcum Powder
News
Contact Us
NEWS CENTER
Company News
Industry News
Technical exchange
Service Hotline: 86-757-22910350
Yuan Lei's Little Knowledge | Take You to Know Transparent Powder
Transparent powder is a non-metallic mineral with high transparency, good whiteness, non-toxic, tasteless, acid and corrosion resistance. With high transparency, the refractive index of the filling material itself is very close to that of most synthetic resins, so the filling amount of the filler does not affect the transparency of the finished product; it can improve the surface smoothness and abrasion resistance of the product; low oil absorption, large filling amount, which is beneficial to reduce the manufacturing cost of the product. Features High transparency: the refractive index of the filling material itself is very close to that of most synthetic resins, so the filling amount of the filler does not affect the transparency of the finished product; High hardness: can improve the surface smoothness and abrasion resistance of the product; Low oil absorption: it is beneficial to reduce the manufacturing cost of the product; Easy to disperse: good wettability to various resins, good adsorption performance, easy to disperse; Strong stability: excellent weather resistance and excellent corrosion resistance. Scope of application Material industry: (transparent paint, PE, PO transparent primer) stearate, transparent acid salt, transparent silica gel, transparent glass glue, etc. Plastic industry: modified transparent powder it has high luminosity, high brightness, high fineness, high transparency and other characteristics, in the blown film, high gloss pp, PE effect is particularly good. Modified transparent powder used in plastics, plastics, rubber and so on. Application recommendations 1. In the high-grade transparent primer, the addition amount of 10-20% is also acceptable. 2, transparent powder added in the primer, due to the increase of the hardness and toughness of the paint film, sanding may have a slight impact. 3, production feeding, in the mixer operation process, should be slow small amount of input, otherwise it may affect its dispersion.
20
2023
/
02
Yuan Lei's Little Knowledge | The Difference between Powder Coatings and Waterborne Coatings
Powder coatings and water-based coatings are a kind of coatings, which are widely used in various industries. In order to let everyone know more about the difference between the two, let's take a look at powder coatings and water-based coatings. powder coating Powder coating is a solid resin and pigments, fillers and additives composed of solid powder synthetic resin coating. water-based coatings A coating that uses water as a solvent or dispersion medium. Water-based coatings do not require a dissolving agent, and are roughly divided into three types of water-soluble coatings, water-diluted coatings, and water-dispersible coatings, and are widely used in the industry. Difference The essential difference between powder coatings and water-based coatings is that one is a liquid coating and the other is a solid coating. Compared with water-based coatings, powder coatings are VOC-free, theoretically 100% utilization, more environmentally friendly. The thickness of one-time coating of powder coating is generally 60 ~ 80u, and it is difficult for liquid to do so. Powder coatings are currently mainly coated by charging, so it is difficult to use all substrates. At present, metal substrates are the main substrates. Liquid does not have this restriction. Powder coatings are difficult to achieve some surface effects of liquid coatings. For example, the mirror effect, even the best powder coating is difficult to avoid defects such as orange peel. Therefore, it is difficult for powder coatings to completely replace liquid coatings. 6. Coating resin system: the resin system of both water-based coatings and powder coatings is quite similar. Popular indoor and outdoor systems are available. The text is all: polyester, epoxy, acrylic and other water-based coatings and powder coatings. Therefore, the use of both occasions, the application industry also has a common, but not completely universal. 7. Water-based coatings can be made with strong metal feeling and bright enough metal effect. The problem that the limited metal particles of powder coating are arranged inside the powder coating, at present, the bonding metal powder can only partially replace the paint or achieve the effect of water-based metal paint. But on the whole, the application of bonding metal powder is still very wide. Water-based coatings and powder coatings on the surface effect of the difference, mainly in the metal effect, plain color effect, almost the same.
17
Yuan Lei's Little Knowledge | Application of Talcum Powder in Coatings
The main component of talc is magnesium silicate containing water, which is white or white-like, fine, sand-free powder, and feels greasy by hand. It has excellent physical and chemical properties. Widely used in cosmetics, medicine and food, coatings, paper, plastics, rubber, cables, ceramics, etc. Let's take a look at the application of talcum powder in coatings. Talc soft texture, low abrasiveness, and has high whiteness, good suspension and dispersion, can be used for white pigment and all kinds of water-based, oil-based, resin-based industrial coatings, primer, protective paint and so on. Talc powder has good suspension and easy dispersion, and low corrosion, in the coating, talcum powder as a filler can play a skeleton role, reduce manufacturing costs and improve the film hardness of the coating. It also has the characteristics of improving the stability of product shape, increasing tensile strength, shear strength, pressure strength, reducing deformation, elongation, thermal expansion coefficient, high whiteness, uniform particle size and strong dispersion. The talcum powder with flake particle structure can make the coating film have high water resistance and impermeability of enamel. The talcum powder with fibrous particle structure can improve the rheological property and leveling property of the coating, and improve the weather resistance of the coating. ▼ From the paint type Primer: Talcum powder can be used in a variety of industrial coatings, especially primers. The primer for steel structure can be used talc powder to improve the precipitation of the coating, the mechanical force of the coating film and the recoatability. Water-based latex coatings: Talcum powder can give it good brushing, leveling, light retention, the resulting coating has good impact resistance and flexibility, but also high corrosion resistance and dry coating. Solvent-based wood coatings: In solvent-based wood coatings, talcum powder is mainly used in PU transparent primer and PU solid color topcoat. Its low hardness helps to improve the polishing property of the paint film. On the other hand, the refractive index of talcum powder is similar to that of resin base material, so the transparency of the coating film is high, which can well reflect the natural texture effect of wood grain of the substrate. Silicate coatings: adding ultra-fine talc powder to silicate coatings can improve the film-forming properties of coatings and improve the performance of coatings. Silicone high temperature resistant coating: because the flake structure of talcum powder can improve the flexural rigidity of high temperature resistant coating at high temperature, so as to improve the adhesion of high temperature resistant coating at high temperature; on the other hand, the functional groups of talcum powder and silicone resin will react chemically under high temperature conditions to form a silicon oxygen bond with certain adhesive force and protective force. The structural stability of the coating is thereby maintained. Other coatings: talcum powder is used for interior wall coatings, which can improve scrub resistance and workability; Used for anti-corrosion coatings, which can improve the protective effect due to the extension of the diffusion path of corrosive substances; Used for polyurethane waterproof coating filler, which can reduce the volume shrinkage of the coating during curing and improve the wear resistance and cohesiveness; It can also act as a separating agent for pigments to improve the coloring effect of pigments.
16
Yuan Lei's Little Knowledge | Application of Nano Calcium Carbonate in Adhesive
Nano calcium carbonate refers to the functional inorganic filler with a particle size of 1-100nm, which is widely used in rubber, plastic, paper, ink, coating, sealant and adhesive, medicine, toothpaste, food and other fields. The following small taping everyone to understand the application of nano calcium carbonate in adhesives. Adhesives are natural or synthetic, organic or inorganic substances that can connect two or more parts or materials together through the adhesion and cohesion of the interface, collectively referred to as adhesives. In short, an adhesive is a substance that binds the adherend together through bonding. As one of the important fillers of adhesives, nano-calcium carbonate not only has low price, but also has good compatibility with adhesives, which can accelerate the crosslinking process of adhesives, improve thixotropy, improve adhesion, tensile strength and reinforcing effect. The technical requirements of nano calcium carbonate used in adhesives mainly include: Oil absorption value: oil absorption value is an index of great concern to silicone rubber manufacturers, which directly affects the wettability of nano calcium carbonate in rubber. Higher nano calcium carbonate has advantages in mechanical properties and thixotropy, but it will lead to colloid viscosity, consume more additives and increase production cost. Different manufacturers' formulation systems have different requirements on oil absorption value of nano calcium carbonate, depending on the specific situation. Crystal form: generally cubic or rhombohedral, but also need to adapt to the technical requirements of the product and production equipment. Particle size: generally controlled at 60 ~ 100nm, if the particle size is too large, it will reduce the mechanical properties of the glue, at the same time will lead to poor thixotropy of the glue, easy to sag; particle size is too small, nano calcium carbonate agglomeration serious, production will make kneading difficult, but also easy to lead to poor dispersion, colloid surface pitting. Moisture: Nano calcium carbonate applied to adhesive requires lower moisture, the better, generally less than 0.5. If the moisture content of nano calcium carbonate is higher, the hydroxyl groups on its surface increase, and the aggregates show a tendency of mutual agglomeration. Under the action of base glue, a three-dimensional network is formed, which increases the viscosity of the glue, resulting in longer mixing time, resulting in lower yield and increased energy consumption. Excessive moisture will also react with glue-making additives to generate particles, resulting in poor dispersion of products, the emergence of particles. In the polyurethane adhesive, containing more isocyanate groups prone to hydrolysis, the generation of CO2 is the product surface foaming phenomenon. pH value: calcium carbonate is a weak alkali salt with a pH value of 8~10. Nano-active calcium carbonate surface coating agent is generally weak organic acid or organic acid salt, which has a certain neutralization effect on its surface. In the production process, the phenomenon of calcium carbonate returning to alkali is very common. If the alkali is not well treated, water will be generated with acidic components in the rubber compound, causing the hydrolysis of siloxane to produce inorganic particles, not only make the appearance of the product worse, but also affect its mechanical properties. Specific surface area: since the particle size is controlled at 60 ~ 100nm, the corresponding specific surface area should be controlled at 20 ~ 25m 2/g. when the specific surface area is too large, although the reinforcing effect is enhanced, it will also lead to poor extrusion performance of the glue and affect the dispersion effect of the product. With the deepening of research and the maturity of technology, nano calcium carbonate will play a greater role in the field of new adhesives.
15
Yuan Lei's Little Knowledge | Indicators of Talcum Powder in Plastic Application
As a plastic filler, talc can not only save the amount of resin used, but also significantly improve the rigidity, impact strength, creep resistance, hardness, surface scratch resistance, heat resistance and heat distortion temperature of the product. The index requirements of talc powder for plastics mainly include purity, whiteness, flake, fineness, SiO content, fluidity, static electricity, etc. Purity: purity refers to the content of talcum powder, nature and industrial production of talcum powder will contain impurities. The higher the purity, the better the enhancement effect. If the content of carbonate, iron, heavy metal and other impurities in talc is high, the aging resistance and thermal stability of plastic products will be poor. Whiteness: Although the level of whiteness has no effect on the physical properties of the product, it is very important to maintain the purity of the color for light-colored products. One disadvantage of talc is that the color of the plastic is more or less darkened after mixing, which is an important factor limiting the widespread use of talc in plastics. The significant strengthening effect of talc on molecular compound plastic products is mainly due to its peculiar microscopic sheet structure. The more complete the flake structure of talcum powder, the more obvious the strengthening effect. The two main factors that affect the flake of the product are: talc purity, powder processing essentials and skills. Fineness: Generally speaking, the finer the finer the better, which is also a major application trend of talcum powder. The higher the fineness of the talc, the better the reinforcing effect. But there is no need to blindly pursue only fineness. At the same time, the particle size distribution of talc powder should be controlled, the more uniform the better, so as to avoid too many coarse particles affecting the effect. SiO₂ content: The silicon (SiO2) content in talc powder is an important indicator to measure the grade of talc powder. According to the performance requirements of different plastic products to choose talcum powder, the film added talcum powder silicon content is higher, the particle size is small, the particle size distribution is narrow, in order to make the index has obvious improvement. In the injection molding, plate, bar silicon content requirements do not have to be too high, low silicon content of talcum powder price is low, while rich in resources. Fluidity: In the extrusion process, talc has poorer fluidity than other granular inorganic materials, is difficult to disperse, and has a large screw torque. Therefore, the use of better activation additives is the key to overcome the above problems. Electrostatic: Talc is easy to produce static electricity, because talc is a layered structure, large specific surface area, irregular particle shape and surface convex and concave morphology make its coefficient of friction large, resulting in the cohesion between tiny particles, difficult to disperse, affecting the use effect. Static storage can be used to eliminate static electricity, which is both practical and easy to operate.
10
Yuan Lei's Little Knowledge | Application and Index Requirements of Nano Calcium Carbonate in Plastics
Nano calcium carbonate refers to the functional inorganic filler with a particle size of 1-100nm, which is widely used in rubber, plastic, paper, ink, coating, sealant and adhesive, medicine, toothpaste, food and other fields. However, different applications have different requirements for the particle size, crystal form, oil absorption value and dispersion of nano-calcium carbonate. The plastic industry is currently the most used industry in the world. It can act as a regulator and enhancer for plastics, and the demand is very large. Due to the good dispersion of nano calcium carbonate, it can well remove the voids and bubbles in the plastic, so that the plastic can shrink more evenly, and improve the mechanical properties and thermal stability of the plastic. The technical requirements of the plastic industry for nano calcium carbonate are: Oil absorption value: the oil absorption value of nano calcium carbonate in the plastic industry is generally very low, because the particle size of nano calcium carbonate is small and the specific surface area is large. If the oil absorption value is large, more plasticizers will be consumed during mixing, which will increase the viscosity of the system, which will not only affect the processing performance, but also increase the production cost. Crystal form: nano calcium carbonate morphology is divided into: cubic, nearly spherical, spindle, rod, chain, needle and so on. Cubes with lower oil absorption value, or the cube part is chain-shaped and spherical is appropriate. Particle size: The particle size of nano calcium carbonate used in plastics is generally controlled at about 80-120nm. Too large particle size cannot reflect the effect of nano calcium carbonate and affect the smooth surface of the product. Too small particle size will lead to an increase in surface energy and serious particle agglomeration. It is not easy to completely disperse during processing, resulting in particles on the surface of the product. Dispersibility: high dispersibility of nano calcium carbonate should be selected. If nano calcium carbonate is seriously agglomerated, the secondary particle size will be much larger than the primary particle size, while the shear force of plastic processing and mixing is not too strong. Some nano calcium carbonate with serious agglomeration is not easy to break up, which will cause local defects and lead to product quality problems during application. Moisture: moisture control should not be higher than 0.5, if the moisture is too high, will make the plastic surface bubbles or empty drum and other phenomena. pH value: the pH value of nano calcium carbonate should be controlled below 10. If the pH value is too high, it will affect the whiteness and surface gloss of the product and make the appearance worse. At the same time, the high pH will also increase the viscosity of the system and affect the processing process. Hydrochloric acid insoluble matter: mainly refers to impurity particles such as black spots and yellow spots in the product, which need to be strictly controlled. Otherwise, when there are more particles, it is easy to cause frequent blockage of the extruder filter screen during processing, affecting production efficiency, and sometimes forming obvious black spots on the surface of the product, affecting the appearance quality of the product. Iron-containing fine particles may increase the yellowness and decrease the whiteness of the product. Special attention should be paid to nano calcium carbonate used for light-colored products. Among all kinds of non-metallic mineral powder materials used in the plastics industry, the amount of calcium carbonate is the largest, accounting for about 60 ~ 70% of the total amount of plastic additives, but there are still many problems in the research of high-performance application, especially how to solve the agglomeration of nano-calcium carbonate, how to improve the dispersion effect of nano-calcium carbonate, how to improve the bonding strength of composite materials and so on.
08