%{tishi_zhanwei}%

Yuan Lei's Little Knowledge | Refractive Index of Powder

Refractive index (1) Absolute refractive index Refers to the refraction of light from the vacuum into the medium, the ratio of the sine of the incident angle I to the refraction angle R is called the "absolute refractive index" of the medium, referred to as "refractive index". That is, the refraction of light when light enters from one angle and comes out from another angle. Because light has this kind of refraction, it will produce a kind of refraction in any medium, and the medium is different, the angle of refraction is different, that is, the refractive index is different, we also refer to the refraction principle of light to make various coatings with different hiding power. (2) the refractive index of the powder in the coating In the production of coatings, the use of different powders will produce different hiding power, and the hiding power of the coating is a combination of the refractive index of various powders and media (I. e. water and resin). When the difference in refractive index between the powder and the medium becomes larger, the hiding power of the coating is strong, otherwise the covering is poor. When the refractive index of the two is the same, the coating film is transparent. The hiding power of powder is mainly determined by its refractive index. Generally, the refractive index of film-forming material is about 1.5. The higher the refractive index of powder, the better the hiding power. We usually call fillers (or physical fillers) when the refractive index is 1.7. It is conducive to the improvement of hiding power, when the amount of more, the coating inside the filler particles around the formation of small air voids, thereby improving the hiding power. For example, the wet hiding power of light calcium carbonate slurry is very poor (because the refractive index of calcium carbonate is 1.58 and that of water is 1.33, which is not much different). However, after drying, water around light calcium carbonate becomes air, and the difference in refractive index becomes larger (the refractive index of calcium carbonate is 1.58 and that of water is 1.0), so the hiding power is improved. Another example: when the film-forming material content is high, the wet hiding power is better than the dry hiding power. The reason for this phenomenon is that water is around the powder when it is wet, and when it is dry, water becomes resin around the powder, the refractive index changes from 1.33 to 1.5, and the difference between the refractive index of powder and resin becomes smaller, so the hiding power becomes worse. This is the use of light calcium after the coating dry cover becomes better. Therefore, in the paint at the same time, we must know some of the basic properties of the powder.

20

2023

/

04

Yuan Lei's Little Knowledge | True Density, False Density and Bulk Density of Powder

True density (true specific gravity) The true density is relative to the bulk density of the particle group, and refers to the actual mass of the solid matter per unit volume of the material in an absolutely dense state, that is, the density after removing the internal pores or the gaps between the particles. True density is the most basic physical parameter of powder materials, and it is also a parameter that must be used to determine other physical properties such as micropowder particle distribution. The value of true density depends on the chemical composition and purity of the material, and its value directly affects the quality, performance and use of the material, which is of great significance to its determination. Formula for calculating true density of pattern: ρ = m/v ρ-true density m-mass of sample v-volume of sample False density (false specific gravity, apparent density) Apparent density refers to the ratio of mass to apparent volume of a material. The apparent volume is the solid volume plus the closed pore volume plus the open pore volume. Apparent density refers to the natural state of the material (dry state stored in the air for a long time) Apparent density = M (solid)/V (solid closed pore open pore) Bulk density (1) Bulk density of powder Bulk density is the mass per unit volume measured by filling dust or powder freely in a container just after filling. The bulk density of the powder occupies a very important position in the use of the powder, because the bulk density of various powders is not the same, the water absorption and specific surface area of the coating is not the same, the resulting porosity of the coating is not the same, directly affect the performance of the coating. The bulk density is measured with a bulk density tester. The bulk density of the powder is mainly due to the size of the powder or the number of days is different, the bulk density can be divided into loose bulk density and tap bulk density. (2) The following is the approximate calculation method of bulk density: Bulk density refers to the quality of powder in the natural accumulation state. Density p = Mass M/Volume V Volume V = True Volume V1 (Void V2 Air V3) It can be seen from the above that in addition to the real physical density of the powder, the bulk density with a certain structural porosity is formed because of the porosity between the air and the powder. The larger the void ratio between the powders is, the larger the volume of the formed powder is, so the smaller the bulk density is. (3) the size of the bulk density and the relationship between the film cover: When the bulk density of the powder used in the coating is smaller, the larger the volume of the powder used, and the greater the porosity of the coating film formed after the volatilization of water between the powders, the stronger the dry cover of the coating film. At the same time, the volume of the powder, the higher the oil absorption, the film's weather resistance and scrub resistance and so on all the performance also have an impact. Therefore, the various properties of the comprehensive powder, the rational use of the characteristics of various powders, in order to reduce the cost of coating production, improve the application performance of the coating.

08

2023

/

04

Yuan Lei's Little Knowledge | Take You to Know Nano Barium Sulfate

Nano barium sulfate has the advantages of good stability, acid and alkali resistance, moderate hardness, high specific gravity, high whiteness, and can absorb harmful rays. It is a material with environmental protection function, so it is widely used in various coatings, medium and high-grade inks, pharmaceutical synthesis Chemical industry, rubber, paper, ceramics, cosmetics and other fields. Scope of application 1. Plastic industry Nano barium sulfate can be added to the polymer (such as polyethylene, polypropylene, polylactic acid, etc.) to obtain high strength, high toughness composite materials. For most polymer composite materials, with the increasing amount of modifier, the strength and toughness of the composite material will increase first and then decrease, and the small amount of modifier will increase the defect of the connection interface between nano-barium sulfate and polymer, resulting in the reduction of the mechanical properties of the composite material. In addition to the influence of the modifier, the amount of barium sulfate is also a certain factor. When the content of nano barium sulfate is too high, it is due to the agglomeration phenomenon in the composite material and the addition of inorganic particles to increase the defects of the matrix, making the composite material more prone to fracture, thus making the mechanical properties of the composite material worse. Therefore, the addition of barium sulfate must be carried out within the scope of its appropriate mechanical properties. 2. Coatings industry Barium sulfate is widely used as an extender pigment in coatings, which plays an important role in improving the thickness, wear resistance, water resistance, heat resistance, surface hardness and impact resistance of the coating film. Because of its low oil absorption and high filling capacity, it can reduce the cost of coatings and replace 10% ~ 25% titanium dioxide in water-based coatings. The results show that the whiteness is improved and the hiding power is not decreased. The characteristics of ultra-fine barium sulfate for coatings are: fine particle size and narrow particle size distribution; Dispersion in resin liquid has transparency; Good dispersion in coating base material; Cooperating with organic coloring pigments has the function of dispersing additives; Can improve physical properties. 3. Paper industry Barium sulfate has the advantages of good physical and chemical stability, moderate hardness, high whiteness, and can absorb harmful rays, so it is often used in the paper industry. 4. Chemical fiber industry Nano-barium sulfate has good nano-effect, while viscose fiber is antistatic, easy to dye, good moisture absorption and easy to textile processing. Nano-barium sulfate/regenerated cellulose blend fiber made of the two as raw materials is a new type of composite fiber, which can maintain the unique properties of each component, and can make up for the shortcomings of a single material through the "synergy" between each other, showing the new properties of composite materials.

06

2023

/

04

Yuan Lei's Little Knowledge | Application of Heavy Calcium, Light Calcium and Nano Calcium in Coatings

Calcium carbonate is the most widely used pigment in coatings, which plays the role of filling the skeleton and substrate in the paint film, and improves the performance of the coating. So what are the applications of heavy calcium carbonate, light calcium carbonate and nano calcium carbonate in coatings? Let's take a look at the following. heavy calcium carbonate Heavy calcium carbonate is the first filler in the world's coating industry. China's coating industry consumes more than 400000 tons of heavy calcium every year. Among them, architectural coatings, paper coatings and powder coatings are the most consumed areas of heavy calcium. (1) As an extender pigment, it has a filling effect to make it delicate, uniform and high whiteness. (2) has a certain dry hiding power, the general use of ultra-fine products, when its particle size and titanium dioxide particle size close, can improve the covering effect of titanium dioxide. (3) can improve the film strength, water resistance, dry, scrub resistance. (4) Improve color retention. (5) Reduce costs, the use of 10% to 50%. Light calcium carbonate Compared with heavy calcium, light calcium is artificially synthesized, and the crystal form and composition are easy to control, so light calcium can be endowed with multiple functions, and the relatively high specific surface area makes the reinforcing effect of powder in the coating obviously better than heavy calcium. (1) As an extender pigment, it has a filling effect, is delicate and increases whiteness. (2) has a certain dry covering power. (3) the density is small, the specific surface area is large, with a certain suspension, play a role in anti-settling. (4) Reduce costs. (5) increase the feel. Disadvantages: easy frosting, swelling, thickening, the amount should not be too large, can not be used in exterior wall coatings. nano calcium carbonate With the rise of nanotechnology, nano calcium carbonate as a cheap nano particles, in the coating industry has become a hot topic, compared with heavy calcium and light calcium, although the cost increases, and has a better reinforcing effect, but nano calcium carbonate in the coating can also improve the coating hiding power, gloss, transparency, quick drying, and stability. In some industries, such as automotive coatings, architectural coatings, etc., nano calcium carbonate can partially or completely replace the high price of titanium dioxide, in order to reduce the cost of enterprises. (1) Building materials: nano calcium carbonate due to the existence of "blue shift" phenomenon, in the latex paint can shield ultraviolet light, play a heat insulation effect, the anti-aging properties of the coating has been improved. Applied to exterior wall coatings, the coatings exhibit strong "hydrophobicity". The cracking strength and contamination resistance of the coating are enhanced. (2) Coating and topcoat: because the nano calcium carbonate particles dispersed in the coating are extremely small, under a certain volume fraction, the number of particles increases sharply, the average distance between particles decreases, and the chance of any two particles entering the mutual attraction zone increases rapidly, resulting in an increase in viscosity. When the material is under stress, the sliding between a large number of particles attracts more impact energy, this is reflected in a wide temperature range with a higher damping value, and the treatment agent layer on the surface of nano calcium carbonate can effectively transfer and relax the stress on the interface between organic and inorganic materials, and better absorb and disperse impact energy. Considering the flexibility of the treatment agent itself, the mechanical strength of the coating film is improved.

03

2023

/

04

Source lei little knowledge | take you to understand what is magnesium powder?

镁强粉,是以超细滑石粉主要原料,配以少量功能性矿物敷料,并经过不同的偶合架桥剂、高级脂肪酸、阴离子界面活性剂等混合处理而成的、具有一定补强功能的粉体填料。镁强粉在油漆、涂料方面耐曝晒、抗高温,在紫外光照射下不变色,能长期保持原有的光泽与色彩,有较好的耐酸碱腐蚀的性能,且耐水性好,耐污染、耐老化性能较强,耐磨、耐蒸汽和化学稳定性,及较强阻燃性能。     『特点』 1,粒度细,质地较硬,可提供平滑的手感。 2,降低光泽,具有良好的平光效果。 3,比表面积和吸油量大,可大量吸油而使增稠效果显著。 4,具有疏水性和亲有机性,耐湿性优异。 5,白度好,遮盖力强,悬浮性能和流变性能优良,可减少产品的流挂和沉降。 6,具有空间位阻等效应,能使配方中的钛白粉均匀分散,从而使钛白粉增量,达到节约部分钛白粉的目的,可取代25-45%的钛白粉,从而降代成本。有其制漆后,漆的贮存稳定性及漆膜的性能均符合要求。 7,它超微细,不需研磨,降低能耗。 8,片状微晶结构,使涂膜能够吸收因膨胀或收缩而产生的压力,使涂膜免于发生裂缝和空隙的病象,施工性和涂刷性大大提高。 9,优良的户外耐久性,耐磨性并可增加漆膜对底材的附着力。 10,PH值呈碱性,包装稳定性和耐锈性优异。     『用途』 1,镁强粉应用于改良橡胶塑胶树脂之压模模、压延、押出、射出等加工性能及可替换部份较昂贵之胶料10-15%来降低原料成本。 2,镁强粉是用在橡胶塑胶树脂中之增胶剂(Plasticizers),尤其是在发泡产品中可助其加工成型,即减少聚合体分子间之摩擦力,使分子键因而容易移动,因此在加工中不论是压模、压出成型,将可促使缩短成型时间提高生产力。 3,镁强粉在聚合体中可使直链型(Linear)分子,经镁强粉架桥作用(Crosslinking)由平面结构变为三度空间之结构(NET-WORK)增强胶模之耐磨、韧性与抗裂作用(Antiblocking Effect)。 4,镁强粉中因聚烯烃在极细(二氧化矽SiO2 . 氧化镁MgO)的表面混合处理,其有助于透明和软硬度的控制,透明的薄膜若加入少量(5-10PHR)镁强粉,则能制得表面极佳之半光性扁系及抗结块(Antibocking)的性质。 5,镁强粉在胶料树脂中,可改变产品之物性---增加张力强度、耐衡击强度、剪切强度、扰曲强度、硬度、降低变形、伸张率、热膨胀系数等。 6,镁强粉与胶料混合后,压延或押出8m/m-10m/m厚度之薄片,有平滑且非常美好的表面,并能迅速减少气泡。 7,镁强粉亦属热安定剂(Heat stabisizers)之一种,因其本身含有高级脂肪酸脂化合物,除了可当橡胶塑胶产品之润滑剂外,还可与析出之Hcl 反应,使Hcl失去裂解之作用。 8,镁强粉可改善触感,并减少静电效果。 9,镁强粉渗入胶料中,可使产品易于印刷及涂饰。 10,镁强粉具有抗氧化剂之功能,因其中含有芳香族化合物可防止聚合体中之键能受热、光或氧的作用断裂,致使胶料之强度降低或变脆,失去应用价值,这种现象在聚烯系塑胶如PVC、EVA 、TPR、PE、ABS及各类橡胶中尤其显著。

28

2023

/

03

< 1...212223...65 >