%{tishi_zhanwei}%

Yuan Lei's Little Knowledge | How to Choose Good Calcium Carbonate

Calcium carbonate (CaCO) is an inorganic compound, commonly known as limestone, limestone, stone powder, marble and so on. Calcium carbonate is neutral, insoluble in water, soluble in hydrochloric acid. It is one of the common substances on the earth, which exists in aragonite, calcite, chalk, limestone, marble, travertine and other rocks. It is also the main component of animal bones or shells. Calcium carbonate is also an important building material and is widely used in industry. The use of calcium carbonate is so wide, so how to distinguish the quality of calcium carbonate, and how to choose a good calcium carbonate? The following methods may help you. We know that calcium carbonate has many excellent characteristics, compared to other powder materials has obvious advantages, such as cheap; good color, easy coloring; low hardness; good thermal stability and chemical stability; easy to dry, no crystal water; non-toxic, non-irritating, tasteless, etc. Therefore, after understanding its characteristics, there are basic requirements for how to choose calcium carbonate. The content of calcium carbonate should be high, and the compounds of silicon, iron and other elements should be as low as possible; 2, the content of harmful heavy metal elements should be more strict requirements; Although the content of harmful heavy metals in calcium carbonate is low and meets the national health level requirements, the content of harmful heavy metals must be strictly required to avoid harm to the human body. 3, whiteness should be as high as possible; Calcium carbonate itself is whiter than other inorganic mineral powders, and it is enough to reach 90 degrees from the specific value. Although the whiteness has no significant effect on the performance of filled plastics, enterprises still hope that the higher the whiteness, the better, mainly based on these reasons: (1) The higher the whiteness, the higher the purity, and the lower the content of other mineral components other than calcium carbonate. The ash of calcium powder indicates that there may be free carbon, the yellow indicates that there may be more iron compounds, and the dark indicates that the content of silicon is high. High impurity content sometimes affects the color and appearance of filled plastic products, and causes heavy wear and tear on processing equipment and molds during processing. (2) The higher the whiteness, the better the intuitive impression, and the higher the grade. (3) the higher the whiteness, with other pigments, the final color is more positive, more stable and uniform. 4. The lower the oil absorption value, the better; The maximum amount of butylene phthalate (DBP) that can be absorbed by 100g of powder material is referred to as the oil absorption value of the material. For some plastic products, such as soft polyvinyl chloride, artificial leather, cable materials, etc., need to use plasticizers, calcium carbonate oil absorption value is higher, the more easy to plasticizer adsorption into the filler, so that it loses the role of plasticized resin, so as to achieve a certain degree of softness need to increase the amount of plasticizer, resulting in rising costs. The oil absorption value can be reduced by surface treatment of calcium carbonate to coat the surface of calcium carbonate particles. For example, the oil absorption value of light calcium carbonate treated with coupling agent can be reduced from 92.91g/100g to 49.33g/100g. 5, fineness and particle size distribution should be appropriate; (1) Considering the cost, as long as it can meet the requirements of use, it is better to use coarse ones than fine ones. (2) Considering the performance of the filled plastic, under the premise that the cost can be appropriately increased, the effect of finer particle size will be better. (3) From the perspective of processing fluidity, under the premise of controlling the maximum particle size, it is better to have a larger average particle size. 6, activation is not activated should be based on the needs of downstream users.

27

2023

/

03

Yuan Lei's Little Knowledge | Types and Properties of Quartz Ore

The main component of quartz is SiO2, colorless and transparent, often containing a small amount of impurities, and become translucent or opaque crystals, hard texture. Quartz is a kind of physical and chemical properties are very stable mineral resources, the crystal belongs to the trigonal system of oxide minerals. Quartz, also known as silica, is mainly the raw material for the production of quartz sand (also known as silica sand), and is also the raw material for quartz refractory materials and ferrosilicon. Quartz ore resources are mainly these types of deposits, namely, natural crystal, quartz sandstone, quartzite, vein quartz, powder quartz and natural quartz sand. 01 Natural Crystal Natural crystal is a quartz crystal mineral, its main component is silicon dioxide (chemical formula: SiO₂), natural crystal alias is water, water jade, etc., usually massive or granular aggregates, generally colorless, gray, milky white, containing other mineral elements is purple, red, smoke (tea), yellow, green and so on. 02 Quartz Sandstone More than 90% of the detrital material of quartz sandstone is quartz detrital, with a few feldspars, rock debris, etc., and few heavy minerals, often stable and rounded heavy minerals, such as tourmaline, maltine, rutile, etc. The main component is silica, with a content of up to 95%-99.5%, which is mainly used in various aspects such as glass raw materials, siliceous refractories, metallurgical auxiliary raw materials and minerals. 03 Quartzite Quartzite is a kind of metamorphic rock mainly composed of quartz, which is formed by metamorphism of quartz sandstone and siliceous rock. Quartzite is generally massive structure, granular metamorphic structure, a crystalline aggregate. The color of quartz is also very rich, common colors are green, gray, yellow, brown, orange red, white, blue, purple, red and so on. 04 vein quartz Vein quartz is a collection of quartz, milky white, gray white, grease luster, compact block, specific gravity of about 2.65, melting point of 1700 ℃ above, good temperature resistance, good acid and alkali resistance, poor thermal conductivity, high insulation, low expansion, stable chemical properties, hardness greater than 7. 05 Powder Quartz The parent rock of natural silt quartz ore is a dense quartzite composed of fine quartz particles with a uniform particle diameter. Under the action of surface weathering, the body is broken and finely broken into powder quartz. The content of silica is 95%-98%, some can be as high as 99%, and the content of Fe2 is 0.04-1%. 06 natural quartz sand Natural quartz sand is a non-metallic mineral substance, its main mineral composition is silica, the color is milky white or colorless translucent, hardness of 7, brittle without understanding, shell-shaped fracture, grease luster, density of 2.65, mainly used in glass, casting, ceramics and refractory materials, smelting ferrosilicon.

23

2023

/

03

Yuan Lei's Little Knowledge | Application of Calcined Kaolin in Architectural Coatings

Kaolin minerals are composed of kaolinite, kaolinite, perlite, halloysite and other kaolinite cluster minerals, the main mineral composition is kaolinite. The crystal chemical formula of kaolinite is 2SiO2 ● Al2O3 ● 2H2O, and its theoretical chemical composition is 46.54% SiO2,39.5% Al2O3, and 13.96% H2O. Kaolin minerals belong to 1:1 type layered silicate. Application of Calcined Kaolin in Building Materials 1, the new gelding material-soil polymer cement. Soil aggregate cement is a new type of cementitious material different from ordinary Portland cement. Polymeric cement is based on kaolin as raw material by low temperature (500-900 ℃) calcination, the following reaction: 2n[Si2O5,Al2(OH)4]→ 2(Si2O5,Al2O2)n+ 4nH2O This reaction transforms the kaolinite structure into metakaolin with amorphous structure, which has high pozzolanic activity. In the metastable state of metakaolin and other amorphous silicon aluminum compounds by alkaline activator and hardening agent, silicon aluminum oxygen compounds experienced a process from depolymerization to polymerization, the formation of some natural minerals in the crust similar to the aluminum silicate network structure. The geopolymeric cement has the link structure of organic polymer, but its basic structure is inorganic silicon oxygen tetrahedron and aluminum oxygen tetrahedron, in which the negative charge is balanced by cations such as alkali metal and alkaline earth metal. 2. Concrete admixture Metakaolin is a white powder of anhydrous aluminum silicate (Al2O3 · 2SiO2) formed by dehydration of kaolin (Al2O3 · 2SiO2 · 2H2O) at an appropriate temperature (500-900 ℃). The average particle size is 1-2 μm, and the content of SiO2 and Al2O3 is more than 90%, especially the content of Al2O3 is higher. The arrangement of atoms in metakaolin is irregular, showing a thermodynamic metastable state, which has strong pozzolanic activity. Metakaolin is easy to react with cement hydration products CH and water to form hydration products, mainly CSH gel, calcium aluminate hydrate and calcium sulphoaluminate hydrate, so it is widely used in concrete admixture to replace silica fume. 3. Paint and coating The main mineral raw materials used in the paint industry are calcium carbonate, talc, titanium dioxide and calcined kaolin. Because kaolin has excellent properties such as chemical inertness, strong covering ability, low cost and high whiteness, calcined kaolin acts as filler and pigment substitute in paint, which can not only control the demand of expensive fuel, but also reduce the production cost. For calcined kaolin, in addition to the above advantages, there are many characteristics: irregular shape, strong optical properties, pigment volume concentration and high oil absorption, wear resistance, not easy to aging, and hiding power is also very high. In the paint industry, its main use is to replace white pigments, especially titanium dioxide; in addition, the particles and types are corresponding to each other, different types of paint with different particles and types of kaolin. For example, the use of coarse particles of calcined kaolin in dull or flat paint; shiny paint requires relatively fine particles of calcined kaolin, and the use of fine-grained kaolin opaque, anti-corrosion characteristics, can also be made of latex materials.

17

2023

/

03

Yuan Lei's Little Knowledge | Application Performance Analysis of Titanium Dioxide in Plastics

Plastic is the second largest user of titanium dioxide, more than 500 titanium dioxide brands in the world, there are more than 50 brands are plastic-specific. The application of titanium dioxide in plastic products can improve the heat resistance, light resistance and weather resistance of plastic products, protect plastic products from UV light, and improve the mechanical and electrical properties of plastic products. It is used in almost all thermosetting and thermoplastic plastics, such as polyolefins (mainly low-density polyethylene), polystyrene, ABS, polyvinyl chloride, etc. It can be mixed with resin dry powder, and can also be mixed with plasticizer-containing liquids, and some titanium dioxide is processed into masterbatches before use. Specific Application Analysis of Titanium Dioxide in Plastics Industry and Color Masterbatch Industry ◆ Plastic industry Most of the plastic with titanium dioxide particle size is relatively fine, usually with titanium dioxide coating particle size of 0.2~0.4 μm, while the plastic with titanium dioxide particle size of 0.15~0.3 μm, so that you can get the blue base phase, the majority of the yellow phase of the resin or easy to yellowing resin shielding effect. Ordinary plastic with titanium dioxide is generally not surface treatment, because the use of conventional hydrated alumina such inorganic coated titanium dioxide, in the relative humidity of 60%, the adsorption balance of water in about 1%, when the plastic in high temperature extrusion processing, water evaporation will lead to smooth plastic surface pores. There are four main quality requirements for titanium dioxide in plastic products, namely, hiding power, whiteness, dispersion and weather resistance. Good hiding power can make plastic products thinner; whiteness determines the appearance of plastic products; poor dispersion of titanium dioxide in plastic products will affect the smoothness and brightness of the products; outdoor use of plastic products and plastic doors and windows must ensure the weather resistance of titanium dioxide. ◆ Masterbatch Plastic masterbatch is a highly concentrated, high-performance color configuration products. It is mainly composed of a core layer (pigment), a coupling layer (coupling agent or surfactant), a dispersion layer (lubricant or dispersant), and a mixing layer (carrier resin). It is used as a coloring agent in plastics and is widely used in the production of plastic products such as blown film, injection molding, hot pressing, and injection molding. Masterbatch can be used for PVC, polyethylene, polypropylene, polystyrene and ABS plastic color matching. Its main components are pigments, resins, dispersants, volume pigments, fluorescent whitening agents, antioxidants, anti-ultraviolet agents, antistatic agents, toughening agents, brighteners, etc., titanium dioxide is used as a white pigment in which it has the advantages of non-toxic, stable chemical properties, high hiding power, and good dispersion. Masterbatch is used as an industrial raw material, and its performance is usually shown in the application of subsequent products (such as film blowing or injection molding). Therefore, the performance of titanium dioxide in color particles is mainly reflected in the application process of color masterbatch, mainly reflected in the coloring ability, whiteness and dispersion processing performance of titanium dioxide, affecting the usage of titanium dioxide, the appearance and gloss of plastic products, and the production cost of color masterbatch.

15

2023

/

03

Source Lei little knowledge, nano calcium carbonate commonly used 10 categories of surface modifiers.

With the gradual expansion of the application field of nano-calcium carbonate, in order to give full play to the advantages of nano-calcium carbonate and improve the performance of nano-calcium carbonate, different surface modification methods and modifiers must be used for surface modification. Let's take a look at the 10 types of surface modifiers commonly used in nano calcium carbonate. 1. Titanate coupling agent Titanate coupling agent can be divided into single alkoxy type, coordination type and chelating type, in order to improve the uniformity of the reaction, the need to use inert solvent for dissolution and dilution, and then in the form of spray surface modification machine, can be better with calcium carbonate particles for dispersion and mixing, surface chemical coating. 2. Aluminate coupling agent The alkoxy at one end of the aluminate can react with the free protons on the surface of calcium carbonate, and the other end can be wound or cross-linked with the polymer molecular chain, and its performance is better than that of titanate. 3. Borate ester coupling agent The use of borate ester coupling agent as a modifier has many advantages: non-toxic and antibacterial, excellent coupling function, good thermal stability, and good hydrolysis resistance. Therefore, boric acid ester as a nano calcium carbonate modifier, not only for dry surface modification process, but also can be used for wet modification treatment. 4. Fatty acid (salt) The mechanism of fatty acid (salt) is to use a large number of hydrophilic hydroxyl groups distributed on the surface of calcium carbonate, showing the characteristics of strong alkalinity, and its RCOO-reacts with Ca2 +, CaHCO3 +, CaOH + and other components in calcium carbonate slurry to generate fatty acid calcium precipitates, which are coated on the surface of calcium carbonate particles, and the hydrocarbon groups in fatty acid calcium make the surface properties of calcium carbonate change from hydrophilic to lipophilic. 5. Phosphate and condensed phosphoric acid Phosphate ester (salt) modifier also belongs to the anionic surfactant, mainly through the phosphate ester corrosion calcium carbonate surface to generate phosphate ester calcium and phosphate hydrogen calcium, which tightly coated on the surface of nano calcium carbonate particles, long chain alkyl outward arrangement, making nano calcium carbonate hydrophobic. 6. Quaternary Ammonium Salts Quaternary ammonium salt is a kind of cationic surfactant, one end of its molecule can be crosslinked with polymer materials, and the other end can be charged with positive electrostatic adsorption on the surface of calcium carbonate. 7. Reactive monomers and active macromolecules In the reactive monomer, small molecule carboxylic acid with unsaturated bond can interact with nano calcium carbonate to disperse nano calcium carbonate; using its reactivity (unsaturated bond), it can be grafted with polyolefin to form a graft and strengthen the interface between nano calcium carbonate and polymer. 8. Polymers The polymer can be adsorbed on the surface of calcium carbonate, so that calcium carbonate has charge characteristics and forms a physical or chemical adsorption layer on the surface of calcium carbonate particles, increases the distance between particles, prevents the adhesion and agglomeration of calcium carbonate particles, and improves the dispersion. Commonly used polymers are mainly oligomers, polymers and water-soluble polymers. 9. Super Dispersant Hyperdispersants are different from traditional surfactants and are mainly composed of a solvent segment and an anchoring segment. The anchoring segment is generally a polar group, which can be tightly combined with the particle surface in the form of single-point anchoring or multi-point anchoring; the solvent segment has different polarities and is suitable for polymer modification with different polarities. 10. Inorganic Inorganic modifiers generally can not make calcium carbonate from hydrophilic to hydrophobic, but can improve the dispersion and acid resistance of nano calcium carbonate, if combined with other modifiers, the effect is better. Commonly used mainly metaphosphoric acid (salt), polyphosphoric acid (salt), aluminate (salt), alum, barium salt, etc.

14

2023

/

03

Yuan lei's little knowledge | what are the advantages and disadvantages of transparent powder as filler

Transparent powder is a non-metallic mineral with high transparency, good whiteness, non-toxic, tasteless, acid and corrosion resistance. With high transparency, the refractive index of the filling material itself is very close to that of most synthetic resins, so the filling amount of the filler does not affect the transparency of the finished product; it can improve the surface smoothness and abrasion resistance of the product; low oil absorption, large filling amount, which is beneficial to reduce the manufacturing cost of the product. Transparent powder is a new type of inorganic filler, which has the characteristics of high transparency, good hardness, good hue, high gloss, good collapse resistance and less dust when used. Widely used in oily furniture paint, decoration paint, adhesives, inks, and plastics. At first, transparent powder was only used in oily wood paint. In a few years, the market reaction gradually changed from unfamiliar and understanding to cautious use and a large number of application stages. From a single paint industry to the paint industry, to the entire chemical industry. Transparent powder also has the characteristics of high toughness, so that the quality of the paint film has been greatly improved, its use value has been recognized by the paint industry, and some well-known enterprises have adopted it in large numbers. Transparent powder has good chemical stability, acid and alkali resistance, and does not contain toxic and harmful substances, allowing customers to use it at ease. Transparent powder as a filler in the application, there are several small problems need to pay attention: 1. High grinding difficulty Because of its high hardness, high toughness will cause the paint film is difficult to polish, which needs to change from the concept, because the hardness, toughness, means that the quality of the paint film is improved, the relative polishing difficulty is also increased. 2. Transparent powder is difficult to prevent settling There are many successful experiences in the paint industry in the anti-sinking of pigments and fillers. Usually, there are two principles of anti-sinking: one is longitudinal anti-sinking and the other is horizontal anti-sinking. As soon as the transverse and longitudinal cross, it will form a reticular structure with the best anti-settling effect. Of course, anti-settling is not absolute. When the paint is thin, there is still a tendency for transparent powder to sink compared with resin, because its specific gravity is larger than that of resin, so the spraying time is required to be adjusted appropriately. 3. Moisture-proof is difficult Some transparent powder on the market is very easy to absorb moisture, so the packaging must be moisture-proof. Transparent powder as a kind of outstanding performance, more economical, environmental protection, the use of more secure functional transparent filling material, will bring a new pattern for the polymer material filling material industry.

09

2023

/

03

< 1...222324...65 >